# Stainless wood screws for outdoor use: A2 or A4, pre-drilling and deck building

Which screw should you use to fix a timber decking board?

On a garden deck exposed to rain, an A2 stainless decking screw is usually a good choice. But if salty slush splashes onto the decking from the road in winter, the higher corrosion resistance of A4 starts to matter. Whether you need to pre-drill depends on something else. At the end of an oak board, for example, an A4 screw still needs the right pilot hole.

[Wood and chipboard screws in the Menet-Trend webshop →](https://shop.menet-trend.hu/:forgacslap-es-facsavarok)

In this article

1. A2 or A4? The decision starts with where the deck is 2. What makes a stainless wood screw a decking screw? 3. When do decking boards need pre-drilling? 4. Building a deck: getting the screw into the board 5. Frequently asked questions

01

## A2 or A4? The decision starts with where the deck is

A2 and A4 denote the material grade of the screw. When choosing, think about what, apart from rainwater, will regularly reach the joint. A screw on a deck facing the garden works in different conditions from one a few metres away, next to a driveway that is salted in winter.

| Where will the screw go? | Which material grade should you choose? |
| --- | --- |
| On a garden deck or balcony where the wood is exposed to rain and humidity | An A2 stainless decking screw is usually suitable. |
| Next to a salted footpath or driveway | A4 is advisable if salty water regularly splashes onto the decking. |
| On a seaside deck, in a place exposed to salt spray | Choose an A4 decking screw recommended for this kind of environment. |
| For timber decking around an outdoor pool | A4 can be the starting point. Check whether the manufacturer also recommends the screw for a place exposed to that particular pool water and its cleaning agents. |

The wood species matters too. Oak and some tropical species, such as bangkirai, contain tannic acid. With these, the wood’s own substances already call for a corrosion-resistant fastener. If an oak deck is also exposed to salty water, take both factors into account together.

02

## What makes a stainless wood screw a decking screw?

On a walking surface you can feel the screw head under bare feet, and the board swells when it gets wet and shrinks as it dries. For visible fixing it is therefore worth looking for a screw recommended specifically for timber decking. A small-diameter head is less conspicuous on the surface. On some types, a separate thread section under the head also helps to hold the board in place on the joist.

To choose the length, measure the thickness of the board and add any spacer. Only the part of the screw that extends beyond these can reach into the joist. If, for example, a thicker board is chosen during the build, the same screw grips less deeply in the substructure. The required penetration depth and the matching screw length are best taken from the size table of the chosen type.

03

## When do decking boards need pre-drilling?

With hardwood and thermally modified decking boards, drill a pilot hole. As it is driven in, the screw forces the wood fibres apart around it. This can cause problems especially at the end of the board, where a crack starting from the hole can easily run out to the end grain. In softwood, a screw designed for this can be driven without pre-drilling, as specified by the manufacturer, but even then it is worth pre-drilling at the board ends. Besides the pilot hole, the specified end distance must also be kept.

What size drill bit do you need? The name “5 mm decking screw” on its own does not tell you. The manufacturer specifies the diameter and depth of the pilot hole to suit the geometry of the screw. Some systems come with a stepped drill bit that drills sections of different diameters in one pass. With hardwood joists, it is especially important to check how deep you also need to pre-drill into the substructure.

04

## Building a deck: getting the screw into the board

- 1. **Lay out the boards and the fixing points.** Work with the gap specified by the decking manufacturer, so that the wood has room to move as its moisture content changes. Where board ends meet, make sure each end has support and enough room for screwing.
- 2. **Mark the holes above the joists.** With wide boards, two fixing points at every joist are common. Fixing on both sides reduces cupping of the board edges. Adjust the exact spacing to the board width and to the requirements of the decking system.
- 3. **Test the joint on an offcut.** Put a piece of the joist timber used on the deck underneath it. Drill the pilot hole, then drive the screw with a bit that fits the screw head exactly. This way, before you fix the first full board, you can see whether the head seats neatly or tears up the fibres around it.
- 4. **Stop at the surface.** With visible fixing screwed from the top, the head should sit as the manufacturer specifies, typically flush with the walking surface. A protruding rim can be felt under bare feet. If, on the other hand, the head sinks deep into the wood and leaves a hollow, set a shallower driving depth for the next screw.

05

## Frequently asked questions

- ### Does an uncovered deck automatically need A4 screws? In an average, freshwater environment, A2 is usually suitable for timber decking exposed to rain. The choice of A4 is justified mainly by salt spray, winter road salt or other increased corrosive exposure.
- ### The decking screw has a self-drilling tip. Can pre-drilling be skipped in oak too? With oak, it is best to follow the hardwood installation instructions for that particular type. Some decking screws have a tip that makes driving easier, yet the manufacturer still recommends pre-drilling them in hardwood.
- ### What changes if the boards go on aluminium profiles instead of timber joists? In that case you need a screw that the manufacturer recommends for fixing timber decking boards to an aluminium substructure. Before ordering, check the wall thickness of the aluminium profile as well as the board thickness.

Looking for wood screws for your next job?

Have the wood species, the board thickness and the substructure material ready. With these details it is easier to choose the right design and size from the Menet-Trend range.

[View wood and chipboard screws in the webshop →](https://shop.menet-trend.hu/:forgacslap-es-facsavarok)

---

HTML: <https://menet-trend.hu/en/nonox-world/stainless-wood-screws-outdoors-a2-a4-decking-screws/>
